Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Cummins 12V Idle Adjustment Q&A

By Jeff Hammaker | Published: 9 Nov 2010

Subject: [RTML] Cummins idle speed How do I adjust the idle speed on my Ram diesel? The idle speed seems too high. First, trace the accelerator linkage to the connection on the fuel pump. With the ENGINE OFF have someone floor the accelerator and watch the fuel arm move. The best position I can describe […]

Stabilizer Kit

By unknown | Published: 23 Oct 2010

Complete stabilizer kit. (Patent Pending) ’94 to ’02 4wd model shown. This product will greatly reduce steering “wander” on your late model Dodge pickup. This unit will serve to eliminate sector shaft play in the steering box which is a large contributor to wandering and poor road feel. It also serves to minimize frame flex […]

Weekend On The Edge 2006

By Dean Isaacson | Published: 11 Nov 2010

You could title this: My travels with Lem – Part II. Here we are on the road to the Weekend on the Edge event hosted by Edge Products of Ogden, Utah. The race is at the Rocky Mountain Raceway in West Valley City, Utah. This photo was taken at a rest stop in Montana. Funny, […]

Cummins 12V Idle Adjustment

By unknown | Published: 22 Oct 2010

Adjusting the idle speed on the diesel engine is not difficult. The adjustment is located on the driver side of the injector pump near the rear of the pump. You will need a 10 mm wrench. Correct speed is: 1994-1998 with AT – in drive with AC on 750 -800 RPM 1994-1998 with manual in […]

Dodge Cummins Under Hood Mods

By dieselminded | Published: 24 Oct 2010

Click picture for a full size view. Click on the product titles below for a link to a dealer OuterWears FAQs (Questions About Prefilters) Why do I need a Pre-Filter? How does a Pre-Filter work? Will adding a Pre-filter reduce my airflow or horsepower? Will the Pre-Filters work on paper filters? How much dirt will […]

Dodge Diesel Injector Comparisons

By unknown | Published: 23 Oct 2010

By popular demand our customers have asked us to show a comparison between the Bosch 275hp RV injector and the Diesel Dynamics True Torque II injector series. This graph shows typical gains with the 275hp RV injectors and DD stages 1,2, and 3. This is a graph of a 99 Cummins Ram with Std Transmission. […]

Boost Gauge Installation on Dodge Cummins

By Andy | Published: 23 Oct 2010

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]

Diesel Filter Water Sediment Drain

By unknown | Published: 23 Oct 2010

Drain the water and sediment from the separator each time the fuel tank is filled. Shut off the engine. Manually open the drain valve until clear fuel is visible. Top Load Filter Type (1) Pull up on the drain valve lever until fluid drains out of the drain tube. If nothing comes out of the […]

Twin Turbos on a Powerstroke Diesel

By dzljim | Published: 24 Oct 2010

A big thanks goes to John Anderson for being the Pioneer on this type of project and sharing his project with all of us. In that same spirit, I threw some pics into a collage to be able to share what I can now, until I can do a formal write up for this site. […]

Transmission Pan Installation Guide

By unknown | Published: 24 Oct 2010

DODGE #727-D TRANSMISSION PAN Please read these instructions and parts list completely before installing this new transmission pan. Consult your owner’s or shop manual for transmission fluid requirements. TOOLS REQUIRED 1/2 socket wrench and driver (for removing the old cover) 1/4 allen bit with a 3/8 ratchet drive (1/4 allen key is furnished) 3/16 allen […]

24V Cummins Fueling System Diagram

By Andy | Published: 22 Oct 2010

1998 CTD No Description 1 Fuel Transfer (Lift) Pump 2 Fuel Return Line (to Fuel Tank) 3 Fuel Supply Line (Low Pressure, to Engine) 4 Fuel Heater 5 Water-in-Fuel (WIF) Sensor 6 Fuel Filter / Water Separator 7 IAT Sensor 8 Map (Boost) Sensor 9 Fuel Drain Manifold 10 CKP Sensor 11 CMP Sensor 12 […]

Installing a Throttle Body Spacer

By Dean Isaacson | Published: 23 Oct 2010

That I take my vehicles to a mechanic, even for minor problems, makes me spoiled in some respects. Though I have disciplined myself to change wiper blades, fuses and light bulbs. Nonetheless, when I looked the throttle body spacer over, I took up the challenge to install the unit myself. This isn't a hard one. […]

Anti-Freeze Replacement

By unknown | Published: 23 Oct 2010

From Steve St.Laurent : Here’s how I did mine and I got approximately 5.5 gallons into the system, first I opened the petcock on the radiator (turn it, then pull on it a little, turn, pull, turn, pull – until it starts draining), that will drain the fluid out of the overflow bottle, once the […]

24V CTD Valve Lash Limits

By unknown | Published: 11 Nov 2010

Spec Intake Exhaust Minimum 0.152 mm (0.006 inch) 0.381 mm (0.015 inch) Standard 0.254 mm (0.010 inch) 0.508 mm (0.020 inch) Maximum 0.381 mm (0.015 inch) 0.762 mm (0.030 inch) Adjustments should only be performed when the engine coolant temperature is less than 60°C (140°F).