Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

NXD Stacker Nitrous System

By rodslinger | Published: 23 Oct 2010

SO you're on the fence about the whole Nitrous issue. Well what if there was a product out there that was mild enough for the daily driver, wouldn't break the bank to purchase and easy enough even the most novice shade tree mechanic could install it? Well here ya go – The guys at Nitrous […]

Clutch Replacement

By unknown | Published: 23 Oct 2010

Start inside the truck. With a Phillips remove the screws holding the shift boot and slide it up. Remove shifter with 3/4″ or 19mm wrench. Pop up transfer case shifter boot and remove bolt/s. Pull out rubber inserts in cupholders and remove bolt/s. Remove plastic shroud. Unbolt shifter boot. Unbolt shift tower carefully and tape […]

Stewart Warner B764 Programmable Speedometer Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B764 Programmable Speedometer Install Sheet Stewart Warner B764 Programmable Speedometer Install Sheet [thanks to Stewart Warner used with permission]

24V Piston Specs

By unknown | Published: 23 Oct 2010

Descriptions Specifications Piston Skirt Diameter 101.864 – 101.88 mm / 4.0104 – 4.011 in Ring Grove Clearance Intermediate Oil Control     0.095 mm / 0.0037 in 0.085 mm / 0.0033 in Top Ring 0.35 – 0.45 mm / 0.014 – 0.0177 in Intermediate 0.85 – 1.15 mm / 0.0334 – 0.0452 in Oil Control […]

Homemade Traction Bars

By dzljim | Published: 23 Oct 2010

With the addition of the 33″ BFG’s and the Detroit Locker, I could feel some wheel hop, with the only real mod being the addition of the 70 hp chip.  Anticipating the increased horsepower my PSD will be putting out, I decided to add traction bars to the rear axle.  Trying to save money for […]

12V Cummins Governor Spring Kit

By unknown | Published: 23 Oct 2010

CAUTION:If you intend to operate the engine over 3200 rpm, you should replace the engine valve springs with a heavy-duty type. If you do not have heavy-duty exhaust springs installed please call PDR for further instructions. Estimated completion time: (First time installer) 1.5 hours Things you will need to complete this project: 1. 7/16″ deep […]

P Pump Cutaway

By dieselminded | Published: 23 Oct 2010

I snapped these Photos at SDX Aneroid Fuel Plate Governor Arm Governor Spring Cover and Throttle Cable Connection Point Governor Springs Pump Cam Delivery Valves Together

Pyrometer Installation

By unknown | Published: 23 Oct 2010

See Universal Installation Guide for Installation on Turbo Down Pipe 1. Remove turbo from exhaust manifold. 2. Stuff a small shop towel or rag 4 to 5 inches into the rear exhaust manifold passage (see pic below) through the turbocharger mounting flange. This is to prevent chips from entering the manifold while drilling and tapping. […]

Tips & Tricks for Better Fuel Economy

By Andy | Published: 24 Oct 2010

1. Air up your tires.Keeping your tires aired up to manufacturers specs can help your fuel economy up. 2. Leave your tailgate up!The tailgate up creates a vortex behind the cab which pushes air up over the tailgate. The tailgate down allows the air to push down on the bed creating drag. 3. Be easy […]

Clutch Tips

By unknown | Published: 23 Oct 2010

Note: Tip 3 is the only one that applies to a Ram pickup TIPS FROM AUTOMOTIVE PRODUCTS, INC. Automotive Products, Inc., the supplier of the Pre- filled Hydraulic Clutch Actuator Assembly for the Dodge Ram (BR), the Dodge Dakota (AN), the Jeep Wrangler (TJ), and the Jeep Cherokee (XJ), has some valuable tips for Automotive […]

7.3L Powerstroke Custom Fuel System

By Andy | Published: 23 Oct 2010

Bigger injectors require more fuel. Lots more fuel than what the oem system can put out. And the oem stuff has many faults, which just makes it that much more appealing to replace the whole darn system! I was planning on doing some work to the truck and I knew it would be laid up […]

Rim Fit

By unknown | Published: 23 Oct 2010

I used fellow TDR member JPittinger’s advice and did the following: Jack up the vehicle, take off rear tires/rims, install 2 lug nuts to hold the drum on. Start the truck, put it in 1st and low range of the transfer case – this makes the drums turn REAL SLOW. If you have an auto, […]

Top 3 Floor Mats for your Diesel Truck

By Andy | Published: 26 Mar 2010

It doesn’t take long to figure out that not all floor mats and liners are the same. Some offer great protection from the elements such as mud, snow, grime and dust, while others offer almost none. If you work in construction or any kind of industry that leavers your boots a little muddy at the […]

Stewart Warner B756 Standard Tachometer Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B756 Standard Tachometer Install Sheet Stewart Warner B756 Standard Tachometer Install Sheet [thanks to Stewart Warner used with permission]

Cummins 12V Fuel PreFilter Cleaning

By unknown | Published: 22 Oct 2010

The maintenance schedule in the owners manual indicates the “strainer” should be cleaned at 12000 mile intervals at the same time the fuel filter is replaced. This is for both the “A” and “B” maintenance schedules. In the instructions in the service manual for replacing the fuel filter it states “Whenever the fuel filter is […]