Post Your Successful Diesel Mods At Dieseldatabase

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Pyro Tap Help

Install Help. Note: Tap Size May Vary [thanks to DIS dieselpage.com used with permission]

Hunting For Horsepower by Alligator Performance

It was a busy Saturday. Trucks were lined up in the vacant lots behind Alligator Performance waiting to get dyno’d. This was Alligator Performance’s first event – and for a small, relatively new company, this was a big event. Alligator Diesel Performance opened their doors in Las Vegas in 2005. In 2009, they moved to […]

Repair Under Hood Weatherstripping

Tired of always finding the weather strip laying on top of the turbocharger in the engine compartment? A bead of silicone rubber RTV in the weatherstrip groove will keep the strip attached and eliminate the fire danger. Red RTV or high strength gray RTV is my favorite for this type of work. Black RTV would […]

Bronco Fuel Tank Mod

When I upgraded my Fuel System pick-ups and returns, and try to plumb a balance line between the front and rear tanks. I found out that the Broncos used a single 33 gallon rear mounted tank. With the combined capacity of about 38 gallons using the OEM F-series tanks, I figured I could loose the […]

Stewart Warner B793 LED Light Kit Install Sheet

Click the link below for the pdf version of Stewart Warner B793 LED Light Kit Install Sheet Stewart Warner B793 LED Light Kit Install Sheet [thanks to Stewart Warner used with permission]

Fuel Filter Usage

Here’s a photo showing the condition of my original fuel filter after 24,000 miles – never been changed to this point since new: The photo is a bit misleading the overall condition of the old filter is actually not bad at all – lots whiter down in between the pleats than can be seen here, […]

Dodge Stock Horsepower Chart

Here’s the stock Horse Power Rating for Cummins / Ram Trucks Year Transmission Stock HP 1994 Auto 160 1994 Manual 175 1994 1 Ton 240 1995 Auto 160 1995 Manual 175 1996 Auto 180 1996 Manual 215 1996 California 180 1997 Auto 180 1997 Manual 215 1997 California 180 1998 12V Auto 180 1998 12V […]

Dodge Diesel Drive Belt Diagram

Location Description 1 Water Pump 2 Belt 3 Tensioner 4 3/8 Hole For Working Tensioner 5 Mount Bolt [thanks to BH used with permission]

Service Record Spreadsheet

Click the link below for the Excel version of Service Record Spreadsheet Service Record Spreadsheet [thanks to WBUSA used with permission]

Performance Chip Comparisons

Fueling and Timing Boxes Etc… Edge Products (www.edgeproducts.com) Edge has a variety of products to unleash the potential of this monster delivering gains up to 120 horsepower and up to 350 foot pounds of torque. The Edge Comp module maximizes engine efficiency by monitoring the RPM, timing, turbo boost pressure and fueling parameters. The module […]

Another Pyrometer Installation

A. THERMOCOUPLE INSTALLATION – The R650 Thermocouple mounts into a 1/4″ pipe thread. If the exhaust manifold is already drilled and tapped, install the thermocouple at that location. If none is provided, make a 3/4″ hole in the exhaust pipe, not more than 6″ below the exhaust-manifold-to-exhaust-pipe connection and weld the R680 bushing into the […]

P Pump Cutaway

I snapped these Photos at SDX Aneroid Fuel Plate Governor Arm Governor Spring Cover and Throttle Cable Connection Point Governor Springs Pump Cam Delivery Valves Together

Adjusting Rear Drum Brakes

For trucks equipped with drum brakes there are a multiple of ways to adjust them. You should be able to get them to adjust automatically by using one of the procedures below. None of them work on my truck and I have to adjust mine manually. I even put all new hardware kits on and […]

Edge EZ Module Manual

[thanks to Edge] Click the link for the pdf version of the Edge EZ Module Manual for the 24V CTD motor. Edge EZ Module Manual

Old 12v Cummins Boost Guage Installation

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]