Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Stewart Warner B833 Gauge Ultra Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B833 Gauge Ultra Shift Light Install Sheet Stewart Warner B833 Gauge Ultra Shift Light Install Sheet [thanks to Stewart Warner used with permission]

P7100 Plunger Lift Timing

By unknown | Published: 23 Oct 2010

Bosch P7100 Lift Specs (mm) P7100 Pumps Only Tolerance for Plunger Lift Timing is +/- 0.1mm ( Use CPL number from engine data plate ) Engine Model B5.9160hpExcept CPL 1968 B5.9160hpCPL 1968 Only B5.9180hp B5.9215hp B5.9California CPL Numbers 1549, 15501551, 15521553, 18151816, 19591839 1968 2022, 2174 2023, 2175 1863 Static InjectionTimingdegrees BTDC Lift in mm […]

Dodge 12V Cummins Throttle Cable Replacement

By unknown | Published: 24 Oct 2010

Throttle cable failure has been common on 1994 – 1998 12 valve diesel engines, usually after about 30,000 miles on the cable. I am now on my third cable, and am curious to see if the new design will be more reliable. Twice I have managed to replace my cable in the nick of time […]

B Series Valve Clearance Adjustment

By dieselminded | Published: 23 Oct 2010

Tools needed: 14mm wrench 15mm wrench 19mm wrench Large Flat blade screwdriver soft mallet or wood block Engine Barring Tool Long 1/2″ drive wrench Torque Wrench feeler gauge NOTE: The Cummins Midrange Performance Tool Kit (P/N 3399869) contains all of the tools required for an oil and oil filter change, a fuel filter change, and […]

Stewart Warner B752 Full Pillar Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B752 Full Pillar Pod Install Sheet Stewart Warner B752 Full Pillar Pod Install Sheet [thanks to Stewart Warner used with permission]

12V TPS Wiring Diagram

By unknown | Published: 24 Oct 2010

For TPS adjustment, Joe G. suggested using a potentiometer in the ground circuit. I decided to try it and It really gives a much better range of adjustment than elongating holes in the TPS body. Here is a schematic drawing showing how to wire it. Using the above circuit, adjusting the potentiometer adds resistance to […]

Dodge 24V IAT Sensor Cleaning

By Dean Isaacson | Published: 23 Oct 2010

This is an article for cleaning the IAT sensor on the 1998-2002 24V diesel engine. The IAT sensor measures the temperature of the intake manifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have […]

Diesel Fault Finding Chart

By unknown | Published: 23 Oct 2010

Symptom Key # symptom 1 Engine Running Hot 2 Poor Transient Response 3 Smoke 4 Engine Lacks Power 5 Black Exhaust Smoke 6 Blue Exhaust Smoke 7 High Oil Consumption 8 Turbocharger Noisy 9 Cyclic Sound From the Turbocharger 10 Oil Leak from Compressor Seal 11 Oil Leak from Turbine Seal   Note: R = […]

Stewart Warner B793 LED Light Kit Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B793 LED Light Kit Install Sheet Stewart Warner B793 LED Light Kit Install Sheet [thanks to Stewart Warner used with permission]

Installing a Banks Technicooler

By Dean Isaacson | Published: 3 Jun 2010

Breathing is one of the basic elements of life. That’s the way God made our bodies and it is embodied in the DNA of the diesel engine. It is ironic that when diesel enthusiasts talk about mods, the first element that comes up is most always the chip. No chip, however, can develop its full […]

Dodge Stock Tire Pressure

By Ken Lenger | Published: 23 Oct 2010

[click image to view larger] [thanks to klenger.net used with permission]

Ford 6.0L Powerstroke Fast Idle Modification

By Andy | Published: 3 May 2011

This mod article will walk you through the steps of installing a Fast Idle Switch. Application: ’05 6.0 PSD with Torque Shift Transmission.   Tools Required: 10mm socket with extension and ratchet Wire striper, cutter, crimp tool At least 5 feet of wire (12-14 gauge, color is user defined) 2 sets of butt or spade […]

How to adjust the idle speed on a Dodge Diesel

By Andy | Published: 22 Oct 2010

How do I adjust the idle speed on my Ram diesel? The idle speed seems too high. First, trace the accelerator linkage to the connection on the fuel pump. With the ENGINE OFF have someone floor the accelerator and watch the fuel arm move. The best position I can describe is that it is under […]

Stewart Warner B759 LED Light Kit Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B759 LED Light Kit Install Sheet Stewart Warner B759 LED Light Kit Install Sheet [thanks to Stewart Warner used with permission]

NXD Stacker Nitrous System

By rodslinger | Published: 23 Oct 2010

SO you're on the fence about the whole Nitrous issue. Well what if there was a product out there that was mild enough for the daily driver, wouldn't break the bank to purchase and easy enough even the most novice shade tree mechanic could install it? Well here ya go – The guys at Nitrous […]