Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

FASS Install

By unknown | Published: 8 Nov 2010

This link is the pdf file for the FASS Install guide. [Thanks Diesel Performance Products] FASS Install

Mixing Gasoline with Diesel Caution

By unknown | Published: 23 Oct 2010

At one time information was released suggesting that a small amount of gasoline mixed with diesel fuel for use in cold weather was an acceptable practice. This information was eventually retracted due to conditions that may result from such a mixture. First and foremost is a safety factor. The gasoline fumes from gasoline are very […]

Cummins 12V Idle Adjustment

By unknown | Published: 22 Oct 2010

Adjusting the idle speed on the diesel engine is not difficult. The adjustment is located on the driver side of the injector pump near the rear of the pump. You will need a 10 mm wrench. Correct speed is: 1994-1998 with AT – in drive with AC on 750 -800 RPM 1994-1998 with manual in […]

24V Cummins Engine Diagram

By unknown | Published: 22 Oct 2010

24V Engine Diagram [click on image for larger version]

Stewart Warner B750 Mechanical Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B750 Mechanical Gauge Install Sheet Stewart Warner B750 Mechanical Gauge Install Sheet [thanks to Stewart Warner used with permission]

Port and Polishing

By unknown | Published: 23 Oct 2010

First, you will need cutters. In the next photo you will see some of the cutters I use for this. On the right are metal cutters. These cost $20 to $75 each, so choose wisely. In the middle are sanding cones. I use #80-100-220-240 grit. I use a long mandrel and a (not shown) short […]

Two Wheel Drive Low

By Andy | Published: 24 Oct 2010

The important thing is the 2 port vacuum switch…you need to get one that is ‘open’ when it’s in the off position so vacuum can flow through normally. I used a Nippondenso EGR vacuum switch for a Honda Civic. They never break! The rest of the parts list is simple and small: Rocker switch (I […]

Installing Upfitter Switches in 2005 and Newer Ford Super-Dutys

By Richard Ray | Published: 23 Oct 2010

If you want to add a few aftermarket options to your new Ford Super Duty, Ford Motor Company makes things easy for you. One of the options you can select from the factory is the “UPFITTER SWITCH” option. This is a bank of four switches, with fuses and associated relays, that provide two 30 amp […]

P7100 Injection Pump Timing

By unknown | Published: 23 Oct 2010

THIS BULLETIN SUPERSEDES TSB. 18-10-94 DATED JUL.. 22, 1994. THE PART NUMBER FOR THE ENGINE TIMING TOOL PACKAGE HAS BEEN CHANGED TO SPX MILLER #6860. Models: 1994 (BR) Ram Truck Symptoms: Excessive white exhaust sake or lack of power. Diagnosis: Using the Mopar Diagnostic System (MDS) or the Scan Tool (DRB II or III) with […]

Cummins Motor Parts and Prices

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Cummins Motor Parts and Prices Cummins Motor Parts and Prices

Bosch VP44 Fuel Injection Pump Replacement

By Kent Earnest | Published: 23 Oct 2010

This documentation is intended to be used as a visual overview only and is not meant to be used as a replacement for a service manual. Please consult your Dodge service manual for complete instructions on the removal and re-installation of an injection pump The truck in this project is a 2000 Dodge Ram 3500 […]

Ford 7.3L Engine Removal – The REAL How To

By dzljim | Published: 23 Oct 2010

After replacing my rear axle cover due to rust through, I noticed severe rust on the engine oil pan. I’ve had experiences with rusted oil pans in the past and knew this had to be taken care of soon, or I’d be doing it in the middle of an Ohio winter. Early October, 2001, I […]

Dodge Stock Horsepower Chart

By unknown | Published: 23 Oct 2010

Here’s the stock Horse Power Rating for Cummins / Ram Trucks Year Transmission Stock HP 1994 Auto 160 1994 Manual 175 1994 1 Ton 240 1995 Auto 160 1995 Manual 175 1996 Auto 180 1996 Manual 215 1996 California 180 1997 Auto 180 1997 Manual 215 1997 California 180 1998 12V Auto 180 1998 12V […]

Rotary Axis Supply Pump Installation 24V CTD

By Dean Isaacson | Published: 8 Nov 2010

[thanks to K-O Engineering] Click the link for the pdf version of the RASP installation manual for the 24V CTD motor. RASP installation manual

Another 24V Lift Pump Replacement Procedure

By Andy | Published: 23 Oct 2010

This is how I replaced the lift pump on my ’99 QC, 4×4. Not sure what variations may or may not accure on other models. Parts list…………..New lift pump, lift pump wire pig tail, banjo bolts washers (8), dielectric grease and approx 1/2 gallon of clean diesel. Tools ………. 3/8″ drive ratchet, 3 or 4 […]