Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Dodge Stock Tire Pressure

By Ken Lenger | Published: 23 Oct 2010

[click image to view larger] [thanks to klenger.net used with permission]

Mixing Gasoline with Diesel

By unknown | Published: 23 Oct 2010

My wise old mechanic who has worked on Mercedes for years told me that if I put one gallon regular gas to a diesel tankfull after about every four tanks that it would perform essentially the same job as a fuel injector cleaner at a fraction of the cost. I would like to hear a […]

12V Cummins Governor Lever Adjustment

By unknown | Published: 23 Oct 2010

Here is the ins and outs of the secret governor lever adjustment This is a cut away view of the governor of a P7100 pump. Notice how the lever hit the cam plate flush at the very bottom edge. To check your adjustment the throttle lever needs to be moved until the lever just touches […]

Edge Power Comp Manual 24V CTD

By Dean Isaacson | Published: 8 Nov 2010

[thanks to Edge] Click the link for the pdf version of the Edge Power Comp Manual for the 24V CTD motor. Edge Power Comp Manual

Two Wheel Drive Low

By Andy | Published: 24 Oct 2010

The important thing is the 2 port vacuum switch…you need to get one that is ‘open’ when it’s in the off position so vacuum can flow through normally. I used a Nippondenso EGR vacuum switch for a Honda Civic. They never break! The rest of the parts list is simple and small: Rocker switch (I […]

Turbo Horsepower

By Andy | Published: 23 Oct 2010

The horsepower is calculated as a rough estimate using approx. 0.7*CFM=Race HP and 0.55*CFM=Daily HP. Turbo CFM Racing HP Daily HP HX35 600 420 330 HX40 800 560 440 T66 800 560 440 B1 900 630 495 H2E 1000 700 550 HX50 1000 700 550 HX55 1050 735 578 HT3B 1100 770 605 T76 1350 […]

Installing a Banks Technicooler

By Dean Isaacson | Published: 3 Jun 2010

Breathing is one of the basic elements of life. That’s the way God made our bodies and it is embodied in the DNA of the diesel engine. It is ironic that when diesel enthusiasts talk about mods, the first element that comes up is most always the chip. No chip, however, can develop its full […]

Port and Polishing

By unknown | Published: 23 Oct 2010

First, you will need cutters. In the next photo you will see some of the cutters I use for this. On the right are metal cutters. These cost $20 to $75 each, so choose wisely. In the middle are sanding cones. I use #80-100-220-240 grit. I use a long mandrel and a (not shown) short […]

B Series Valve Clearance Adjustment

By dieselminded | Published: 23 Oct 2010

Tools needed: 14mm wrench 15mm wrench 19mm wrench Large Flat blade screwdriver soft mallet or wood block Engine Barring Tool Long 1/2″ drive wrench Torque Wrench feeler gauge NOTE: The Cummins Midrange Performance Tool Kit (P/N 3399869) contains all of the tools required for an oil and oil filter change, a fuel filter change, and […]

Dodge 12V Cummins Fuel Shutdown Solenoid

By unknown | Published: 23 Oct 2010

To check the fuel solenoid adjustment: 1. Turn the key on but do not bump the starter 2. Get under hood and pull up the solenoid by hand (it will stay up when you let go). 3. Measure from the bottom of the solenoid mounting bracket to the top of the lever pin as shown […]

Pyrometer Installation

By unknown | Published: 23 Oct 2010

See Universal Installation Guide for Installation on Turbo Down Pipe 1. Remove turbo from exhaust manifold. 2. Stuff a small shop towel or rag 4 to 5 inches into the rear exhaust manifold passage (see pic below) through the turbocharger mounting flange. This is to prevent chips from entering the manifold while drilling and tapping. […]

Dodge 24V Cummins Lift Pump Replacement

By unknown | Published: 23 Oct 2010

Procedures for a 1999 Ram NOTE: You may be able to improve this but this is exactly what we did and changed two pumps in less that two hours) TOOLS: 17 mm wrench & socket, 10 mm wrench & socket, 7/16 socket, 1/2 inch socket. 1. Lay a non-conducting material over the battery posts (fender […]

Exhaust Stack Gallery

By unknown | Published: 23 Oct 2010

  Submit Yours !!!!

Rust Prevention

By unknown | Published: 23 Oct 2010

Here’s a convenient and easy method of applying rust preventing solutions to inner panels and seams to control or avoid rust to various body seams. The nicest feature, is that you don’t have to remove interior panels to apply, just insert the feed hose into where you want to apply your rustproofing. The specific solutions […]

Ram Injector Specs

By unknown | Published: 23 Oct 2010

Fuel Injector ” Pop Off ” Pressure: 31,026 kPa (310 bars) or (4500 psi +/- 250 psi) Fuel Injector Leak Down Pressure: App 20 bars (291 psi) lower than pop pressure Fuel Injector Firing Order: 1-5-3-6-2-4