Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Cummins 12V Fuel PreFilter Cleaning

By unknown | Published: 22 Oct 2010

The maintenance schedule in the owners manual indicates the “strainer” should be cleaned at 12000 mile intervals at the same time the fuel filter is replaced. This is for both the “A” and “B” maintenance schedules. In the instructions in the service manual for replacing the fuel filter it states “Whenever the fuel filter is […]

Tips & Tricks for Better Fuel Economy

By Andy | Published: 24 Oct 2010

1. Air up your tires.Keeping your tires aired up to manufacturers specs can help your fuel economy up. 2. Leave your tailgate up!The tailgate up creates a vortex behind the cab which pushes air up over the tailgate. The tailgate down allows the air to push down on the bed creating drag. 3. Be easy […]

Stewart Warner B774 In-Dash Mount Bracket Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B774 In-Dash Mount Bracket Install Sheet Stewart Warner B774 In-Dash Mount Bracket Install Sheet [thanks to Stewart Warner used with permission]

24V Cummins Fueling System Diagram

By Andy | Published: 22 Oct 2010

1998 CTD No Description 1 Fuel Transfer (Lift) Pump 2 Fuel Return Line (to Fuel Tank) 3 Fuel Supply Line (Low Pressure, to Engine) 4 Fuel Heater 5 Water-in-Fuel (WIF) Sensor 6 Fuel Filter / Water Separator 7 IAT Sensor 8 Map (Boost) Sensor 9 Fuel Drain Manifold 10 CKP Sensor 11 CMP Sensor 12 […]

Stewart Warner B779 Add-On Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner Add-On Shift Light Install Sheet Stewart Warner Add-On Shift Light Install Sheet [thanks to Stewart Warner used with permission]

Stewart Warner B833 Gauge Ultra Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B833 Gauge Ultra Shift Light Install Sheet Stewart Warner B833 Gauge Ultra Shift Light Install Sheet [thanks to Stewart Warner used with permission]

FASS Install

By unknown | Published: 8 Nov 2010

This link is the pdf file for the FASS Install guide. [Thanks Diesel Performance Products] FASS Install

12V TPS Wiring Diagram

By unknown | Published: 24 Oct 2010

For TPS adjustment, Joe G. suggested using a potentiometer in the ground circuit. I decided to try it and It really gives a much better range of adjustment than elongating holes in the TPS body. Here is a schematic drawing showing how to wire it. Using the above circuit, adjusting the potentiometer adds resistance to […]

Cummins Governor Spring Replacement Aid

By dieselminded | Published: 23 Oct 2010

Here’s the dust cover that needs to be removed to access the governor springs Once the dust cover is removed you’ll need to turn the motor over till a set of springs is lined up perfectly in the opening … there are 2 sets of springs they are mounted opposite of each other Here’s how […]

Hunting For Horsepower by Alligator Performance

By Dean Isaacson | Published: 21 Oct 2011

It was a busy Saturday. Trucks were lined up in the vacant lots behind Alligator Performance waiting to get dyno’d. This was Alligator Performance’s first event – and for a small, relatively new company, this was a big event. Alligator Diesel Performance opened their doors in Las Vegas in 2005. In 2009, they moved to […]

Dodge Truck Front Disc Brake Replacement

By dieselminded | Published: 10 Nov 2010

Work Performed On: 2002 CTD Estimated time of Completion: 2 Hrs Parts Required: Brake Shoes, Brake Cleaner, Brake Fluid, Little Helper Tools Required: 1/2 Inch Drive Ratchet, Cheater Pipe, 2 Extensions, 15/16 6 pt Socket, 7/32 Allen Wrench, 16 MM 12 pt Socket, Big Strait Screw Driver, Floor Jack, Penetrating Oil, 3/8 inch wrench Product […]

Old 12v Cummins Boost Guage Installation

By Andy | Published: 23 Oct 2010

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]

Ram Diesel Lift Pump Replacement

By unknown | Published: 23 Oct 2010

Tools needed: 7/16 or 11mm socket – for boost tube clamps 10mm socket – for lift pump bolts 14mm socket – for fuel filter canister 3/8 ratchet 6″ 3/8 extension 3/8 universal joint – makes filter nut easier 3/4″ open end wrench – for fuel inlet nut 14mm open end wrench – for fuel outlet […]

Dodge Cummins HTT Manifold

By Kevin Whitmore | Published: 23 Oct 2010

After much reading of folks having troubles with the OEM manifold cracking and the bolts coming loose from expansion and contraction I decided it was time for me to go to a 3 piece manifold, I opted for the unit from High Tech Turbo and purchased one from my friend Lazer Bob in Colorado, The […]

Truck Domains or Website – Dieseldatabase Can Help!

By Dean Isaacson | Published: 7 Mar 2010

Are you looking to start a truck blog? or do you want a website to show off your truck? We can help you. Cougar Gulch Group, LLC (the Diesel Database people) have several domain names for lease or for sale. We have full-featured, CMS websites (WordPress/Thematic) available from $150 to $499 (or more) and it […]