Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Stewart Warner B749 Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B749 Gauge Install Sheet Stewart Warner B749 Gauge Install Sheet [thanks to Stewart Warner used with permission]

Stewart Warner B750 Mechanical Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B750 Mechanical Gauge Install Sheet Stewart Warner B750 Mechanical Gauge Install Sheet [thanks to Stewart Warner used with permission]

Stewart Warner B751 Air Fuel Ratio Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B752 Air Fuel Ratio Gauge Install Sheet Stewart Warner B752 Air Fuel Ratio Gauge Install Sheet [thanks to Stewart Warner used with permission]

Stewart Warner B757 Ultra Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B757 Ultra Shift Light Install Sheet Stewart Warner B757 Ultra Shift Light Install Sheet [thanks to Stewart Warner used with permission]

Cleaning Stickum – Part 2

By Dean Isaacson | Published: 23 Oct 2010

This is a followup article to Cleaning Stickum Left From Vinyl After the last article regarding removing the stickum leftover from vinyl lettering and signs, several people got hold of me to let me know of their remedies. DM left a comment on the article site about peanut butter removing residue left behind by decals. […]

Homemade Traction Bars

By dzljim | Published: 23 Oct 2010

With the addition of the 33″ BFG’s and the Detroit Locker, I could feel some wheel hop, with the only real mod being the addition of the 70 hp chip.  Anticipating the increased horsepower my PSD will be putting out, I decided to add traction bars to the rear axle.  Trying to save money for […]

Stewart Warner B752 Full Pillar Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B752 Full Pillar Pod Install Sheet Stewart Warner B752 Full Pillar Pod Install Sheet [thanks to Stewart Warner used with permission]

Dodge Cummins Fan Removal

By unknown | Published: 23 Oct 2010

The thread is left hand; from the front of the engine you turn the wrench to the right (toward the driver side). Do this when the engine is cool. Some people pull the entire fan/hub assembly out past the radiator shroud, others remove the fan first, then remove the hub. In many cases, a drift […]

Inspecting the Water Pump Weep Hole on Dodge Diesel Trucks

By unknown | Published: 23 Oct 2010

Use a pipe cleaner or a piece of wire to knock scale and dirt from the water pump weep hole. 1st and 2nd generation (every 12000 miles): 1: From above and just in front of the alternator pulley, look down to the water pump. 2: The weep hole is at about the 7:00 position, below […]

Rim Fit

By unknown | Published: 23 Oct 2010

I used fellow TDR member JPittinger’s advice and did the following: Jack up the vehicle, take off rear tires/rims, install 2 lug nuts to hold the drum on. Start the truck, put it in 1st and low range of the transfer case – this makes the drums turn REAL SLOW. If you have an auto, […]

Hunting For Horsepower by Alligator Performance

By Dean Isaacson | Published: 21 Oct 2011

It was a busy Saturday. Trucks were lined up in the vacant lots behind Alligator Performance waiting to get dyno’d. This was Alligator Performance’s first event – and for a small, relatively new company, this was a big event. Alligator Diesel Performance opened their doors in Las Vegas in 2005. In 2009, they moved to […]

APPS Repair

By unknown | Published: 23 Oct 2010

This guide addresses the construction, possible disassembly, and possible repair of erratic or failed APPS units. These throttle control units, APPS (Accellerator Pedal Position Sensor), most frequently seem to fail or become erratic in operation due to deteriorating contact between internal rotating fingers and the resistance track they ride on inside the APPS unit, causing […]

Diesel Thunder 2006

By Dean Isaacson | Published: 23 Oct 2010

Lem stayed up late the night before and was working into the morning installing the Snow Performance water/methane injection system on his 2002 Cummins. As a result, we were late to the Dyno Drags for this year’s Diesel Thunder hosted by Northwest Bombers (local division of TDR). I and our friend Thom, who was working […]

Gauge Installation Prep

By dieselminded | Published: 23 Oct 2010

This is a NEW USERS guide to gauge install preparation. I wish that I had something similar to this when I started this project. So I have assembled the information in this document with the goal of helping people to prepare for installing gauges. Some of This information has been obtained from Turbo Diesel Registry […]

Cummins Valve Cover Replacement

By dieselminded | Published: 10 Nov 2010

Here’s the Stocker And here’s the Bombed Valve cover Available Here at the Database: check the marketplace :: Bob Wagner The only tools you’ll need is a 1/4 inch drive ratchet and a 10 MM socket Really clean up the stock valve cover you do not want anything to fall down in to the valves […]