Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Dodge 24V Cummins Lift Pump Replacement

By unknown | Published: 23 Oct 2010

Procedures for a 1999 Ram NOTE: You may be able to improve this but this is exactly what we did and changed two pumps in less that two hours) TOOLS: 17 mm wrench & socket, 10 mm wrench & socket, 7/16 socket, 1/2 inch socket. 1. Lay a non-conducting material over the battery posts (fender […]

A Recommendation for Trailer Pullers

By Wes Bailor | Published: 23 Oct 2010

I pull a 27 foot fifth-wheel RV trailer. I’ve had it all over the West. As you know, there is a hill or two out here. In fact just south of my town, Bend, Oregon, there is a grade that slowed my previous truck with this trailer to 45 mph top speed. I’ve always hated […]

Top 3 Floor Mats for your Diesel Truck

By Andy | Published: 26 Mar 2010

It doesn’t take long to figure out that not all floor mats and liners are the same. Some offer great protection from the elements such as mud, snow, grime and dust, while others offer almost none. If you work in construction or any kind of industry that leavers your boots a little muddy at the […]

Waste Gate Mods

By dieselminded | Published: 10 Nov 2010

The simple explanation: a waste gate limits the maximum boost generated by the turbocharger. How it works and what it does: The waste gate uses a pressure activated diaphragm and rod to operate an exhaust bypass around the turbocharger and thus limit the maximum boost that the turbocharger can produce. This permits an engine manufacturer […]

Turbo Troubleshooting Chart

By unknown | Published: 24 Oct 2010

Click on Image for a Larger View [thanks to Garrett used with permission]

Dodge Diesel Truck Buyers Guide

By unknown | Published: 23 Oct 2010

Every Vehicle, Every Model On earth has its fair share of issues, And our CTD/RAMS are no exception This article is not meant to point out problems you’re going to have its just a heads up to some common known issues. To Learn Even More Join www.TDR1.com These Problems Affect all Years: Steering wander, 5th […]

24V CTD Valve Lash Limits

By unknown | Published: 11 Nov 2010

Spec Intake Exhaust Minimum 0.152 mm (0.006 inch) 0.381 mm (0.015 inch) Standard 0.254 mm (0.010 inch) 0.508 mm (0.020 inch) Maximum 0.381 mm (0.015 inch) 0.762 mm (0.030 inch) Adjustments should only be performed when the engine coolant temperature is less than 60°C (140°F).

Turbo Horsepower

By Andy | Published: 23 Oct 2010

The horsepower is calculated as a rough estimate using approx. 0.7*CFM=Race HP and 0.55*CFM=Daily HP. Turbo CFM Racing HP Daily HP HX35 600 420 330 HX40 800 560 440 T66 800 560 440 B1 900 630 495 H2E 1000 700 550 HX50 1000 700 550 HX55 1050 735 578 HT3B 1100 770 605 T76 1350 […]

B Series Valve Clearance Adjustment

By dieselminded | Published: 23 Oct 2010

Tools needed: 14mm wrench 15mm wrench 19mm wrench Large Flat blade screwdriver soft mallet or wood block Engine Barring Tool Long 1/2″ drive wrench Torque Wrench feeler gauge NOTE: The Cummins Midrange Performance Tool Kit (P/N 3399869) contains all of the tools required for an oil and oil filter change, a fuel filter change, and […]

Twin Turbos on a Powerstroke Diesel

By dzljim | Published: 24 Oct 2010

A big thanks goes to John Anderson for being the Pioneer on this type of project and sharing his project with all of us. In that same spirit, I threw some pics into a collage to be able to share what I can now, until I can do a formal write up for this site. […]

Dodge 12V Cummins Throttle Cable Replacement

By unknown | Published: 24 Oct 2010

Throttle cable failure has been common on 1994 – 1998 12 valve diesel engines, usually after about 30,000 miles on the cable. I am now on my third cable, and am curious to see if the new design will be more reliable. Twice I have managed to replace my cable in the nick of time […]

Rim Fit

By unknown | Published: 23 Oct 2010

I used fellow TDR member JPittinger’s advice and did the following: Jack up the vehicle, take off rear tires/rims, install 2 lug nuts to hold the drum on. Start the truck, put it in 1st and low range of the transfer case – this makes the drums turn REAL SLOW. If you have an auto, […]

Stewart Warner B821 Quad Console Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner Quad Console Pod Install Sheet Stewart Warner Quad Console Pod Install Sheet [thanks to Stewart Warner used with permission]

Fast Idle Modification

By James Wiger | Published: 10 Nov 2010

This mod article will walk you through the steps of installing a Fast Idle Switch. Application: ’05 6.0 PSD with Torque Shift Transmission.   Tools Required: 10mm socket with extension and ratchet Wire striper, cutter, crimp tool At least 5 feet of wire (12-14 gauge, color is user defined) 2 sets of butt or spade […]

Turbo Comparison Photos

By dieselminded | Published: 24 Oct 2010

Here are some comparison photos of After Market Turbos compared to Stock Equipment Click on images for a larger view. Thanks To : Henry H Wyatt II From left to right 02′ Stock, HX 40, HT3B (from piers street twin setup) HY35 vs B 1-2 Thanks To : Bill Soule