Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Dodge Stock Tire Pressure

By Ken Lenger | Published: 23 Oct 2010

[click image to view larger] [thanks to klenger.net used with permission]

Dodge Stock Horsepower Chart

By unknown | Published: 23 Oct 2010

Here’s the stock Horse Power Rating for Cummins / Ram Trucks Year Transmission Stock HP 1994 Auto 160 1994 Manual 175 1994 1 Ton 240 1995 Auto 160 1995 Manual 175 1996 Auto 180 1996 Manual 215 1996 California 180 1997 Auto 180 1997 Manual 215 1997 California 180 1998 12V Auto 180 1998 12V […]

Stewart Warner B833 Gauge Ultra Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B833 Gauge Ultra Shift Light Install Sheet Stewart Warner B833 Gauge Ultra Shift Light Install Sheet [thanks to Stewart Warner used with permission]

Exhaust Stack Gallery

By unknown | Published: 23 Oct 2010

  Submit Yours !!!!

Relocating Your Block Heater Cord

By unknown | Published: 23 Oct 2010

As you know the block heater plug on our trucks are located in the front bumper and this is where they stay for most people. Some have put a plug recessed into the bumper to make it look nicer then having a cord dangling there. In my case being a Firefighter the way I park […]

Dodge Cummins Cooling Capacity

By unknown | Published: 11 Nov 2010

5.9 L CTD 22.7 L or 24 Quarts Includes 1 quart for reservoir

Pyro Tap Help

By dieselminded | Published: 23 Oct 2010

Install Help. Note: Tap Size May Vary [thanks to DIS dieselpage.com used with permission]

Exhaust Stacks

By unknown | Published: 23 Oct 2010

I built this setup from scratch and ran it for only 1 month before removing and reinstalling my 4″ system. This system sounded very good but had some draw backs that I couldn’t live with including noise and smoke for passengers in the back and soot showers on startup after a rain or carwash (there […]

Dodge Cummins Fan Removal

By unknown | Published: 23 Oct 2010

The thread is left hand; from the front of the engine you turn the wrench to the right (toward the driver side). Do this when the engine is cool. Some people pull the entire fan/hub assembly out past the radiator shroud, others remove the fan first, then remove the hub. In many cases, a drift […]

Dodge Pickup VIN Decoding

By unknown | Published: 11 Nov 2010

The Vehicle Identification Number (VIN) plate is located on the dash by the windshield near the left A-pillar. Position Interpretation Code Description 1 Country Of Orgin 3 Mexico 2 Make 8 Dodge 3 Vehicle type 6 Incomplete 7 Truck 4 Gross Vehicle Weight Rating K 8,001 – 9,000 M 10,001 – 14,000 5 Vehicle line […]

Heated Tow Mirror Swap

By unknown | Published: 23 Oct 2010

You need to have the bases from an 2nd gen. tow mirror equipped truck. Then purchase a set of Power/heated tow mirrors from a 3rd gen truck, you can get them in a kit (which is both mirrors, you will still need to buy a switch, knob and nut) Once you have all four mirrors, […]

Homemade Traction Bars

By dzljim | Published: 23 Oct 2010

With the addition of the 33″ BFG’s and the Detroit Locker, I could feel some wheel hop, with the only real mod being the addition of the 70 hp chip.  Anticipating the increased horsepower my PSD will be putting out, I decided to add traction bars to the rear axle.  Trying to save money for […]

24V Cummins Fueling System Diagram

By Andy | Published: 22 Oct 2010

1998 CTD No Description 1 Fuel Transfer (Lift) Pump 2 Fuel Return Line (to Fuel Tank) 3 Fuel Supply Line (Low Pressure, to Engine) 4 Fuel Heater 5 Water-in-Fuel (WIF) Sensor 6 Fuel Filter / Water Separator 7 IAT Sensor 8 Map (Boost) Sensor 9 Fuel Drain Manifold 10 CKP Sensor 11 CMP Sensor 12 […]

Installing a Banks Technicooler

By Dean Isaacson | Published: 3 Jun 2010

Breathing is one of the basic elements of life. That’s the way God made our bodies and it is embodied in the DNA of the diesel engine. It is ironic that when diesel enthusiasts talk about mods, the first element that comes up is most always the chip. No chip, however, can develop its full […]

Rotary Axis Supply Pump Installation 24V CTD

By Dean Isaacson | Published: 8 Nov 2010

[thanks to K-O Engineering] Click the link for the pdf version of the RASP installation manual for the 24V CTD motor. RASP installation manual