Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

On Board Air Tank

By dzljim | Published: 23 Oct 2010

It’s always handy to have compressed air with you for filling your flat tires, other people’s flat tires, air horns, blowing mulch or straw out of your bed, the list can go on and on.  I use compressed air mainly for my air horns. I’ve had a 9 gallon air tank in my aluminum bed […]

How to adjust the idle speed on a Dodge Diesel

By Andy | Published: 22 Oct 2010

How do I adjust the idle speed on my Ram diesel? The idle speed seems too high. First, trace the accelerator linkage to the connection on the fuel pump. With the ENGINE OFF have someone floor the accelerator and watch the fuel arm move. The best position I can describe is that it is under […]

24V Transmission Band Adjustment

By dieselman | Published: 24 Oct 2010

One of the most frequent questions I get on the Cummins powered Dodge trucks is transmission related. The Dodge automatic tranny is very robust and does what it was intended to do very well. But given the reputation for massive torque that the Cummins engine provides, many times the transmission is asked to do far […]

A Good Chain Can Make All The Difference

By Dean Isaacson | Published: 23 Oct 2010

I cannot describe the feeling but I know you’ve felt it before. The feeling you get when you know something is enormously wrong but just before the full impact hits you. It was only five fifteen but it was dark outside. I stepped outside my truck and was looking back at the trailer. From where […]

Cummins Motor Parts and Prices

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Cummins Motor Parts and Prices Cummins Motor Parts and Prices

Dodge Cummins 12V Dowel Repair

By unknown | Published: 22 Oct 2010

Several people on the TDR website showed interest in learning more about the work involved in replacing a broken timing gear housing from damage caused by the upper dowel pin working its way loose. You first remove the bumper, fan, radiator and loosen the A/C condenser. It is possible to remove the intercooler without breaking […]

Stewart Warner B753 Pillar Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B753 Pillar Pod Install Sheet Stewart Warner B753 Pillar Pod Install Sheet [thanks to Stewart Warner sw-performance.com used with permission]

Clutch Replacement

By unknown | Published: 23 Oct 2010

TOOLS: Tranny jack 2 or 3 ratchet straps porta power (this will make removing the cross member MUCH eaiser) A bottle jack and a piece of 4×4 will work in a pinch. Drill a hole in the end of the 4×4 to allow the bottle jack shaft to go in the 4×4 a couple of […]

Cummins 12V Fuel PreFilter Cleaning

By unknown | Published: 22 Oct 2010

The maintenance schedule in the owners manual indicates the “strainer” should be cleaned at 12000 mile intervals at the same time the fuel filter is replaced. This is for both the “A” and “B” maintenance schedules. In the instructions in the service manual for replacing the fuel filter it states “Whenever the fuel filter is […]

Bronco Fuel Tank Mod

By dzljim | Published: 23 Oct 2010

When I upgraded my Fuel System pick-ups and returns, and try to plumb a balance line between the front and rear tanks. I found out that the Broncos used a single 33 gallon rear mounted tank. With the combined capacity of about 38 gallons using the OEM F-series tanks, I figured I could loose the […]

12V Engine Diagram

By unknown | Published: 22 Oct 2010

Here is a Dodge 12V Cummins Engine Diagram Click on the image for a larger version.

Boost Gauge Installation on Dodge Cummins

By Andy | Published: 23 Oct 2010

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]

Inspecting the Water Pump Weep Hole on Dodge Diesel Trucks

By unknown | Published: 23 Oct 2010

Use a pipe cleaner or a piece of wire to knock scale and dirt from the water pump weep hole. 1st and 2nd generation (every 12000 miles): 1: From above and just in front of the alternator pulley, look down to the water pump. 2: The weep hole is at about the 7:00 position, below […]

My Glowplug Relay Bypass System

By dzljim | Published: 23 Oct 2010

There have been many threads on the glow plug relay bypass idea discussing how and when to turn off the relay, and even whether or not it is a good idea at all. I have come up with a combination of ideas that I feel is the best scenario. How the glow plugs work depends […]

Installing a Banks Technicooler

By Dean Isaacson | Published: 3 Jun 2010

Breathing is one of the basic elements of life. That’s the way God made our bodies and it is embodied in the DNA of the diesel engine. It is ironic that when diesel enthusiasts talk about mods, the first element that comes up is most always the chip. No chip, however, can develop its full […]