Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Windshield Wiper Motor Replacement

By dieselminded | Published: 10 Nov 2010

[A] Gently pry up on the little tap this will release a small piece of metal that just slides under the gear. After clip is released you will have to pry the WSW bottom off the gear this is the bad part — took longer to get the WSW off the gear then it did […]

Superchips Installation Guide 3705

By unknown | Published: 9 Nov 2010

Click the link below for the pdf version of the Superchips Installation Guide for the 3705 Superchips Installation Guide for the 3705

Vulcan Fittings

By dieselminded | Published: 10 Nov 2010

This is a comparison between a Vulcan fitting and your stock banjo set up. The Vulcan Fittings are CNC Stainless Steal and are avalible with a tap in them for running a Fuel Pressure gauge. Vulcans Fitting replace The Stock Banjo’s at the following locations : VP44 inlet Fuel Filter Housing Inlet Fuel Filter Housing […]

Crankshaft Position Sensor Replacement

By unknown | Published: 23 Oct 2010

(1) you need to disconnect both negative battery cables at both batteries. I used a 1/2 inch deep socket to remove the cables from the battery terminals. (2) Remove starter motor to get to CKP. The sensor is located on the driver’s side of the engine with the starter motor placed in front of it. […]

Clamp On Isspro Thermocoupler

By unknown | Published: 23 Oct 2010

Locate the pipe running from the exhaust manifold on the drivers side over to the turbo. About 2″ above where this pipe attaches to the exhaust manifold a hole can be drilled to accommodate the thermocouple. Start with a small drill bit and work up to 1/4″ one bit size at a time making sure […]

Stewart Warner B821 Quad Console Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner Quad Console Pod Install Sheet Stewart Warner Quad Console Pod Install Sheet [thanks to Stewart Warner used with permission]

Cummins 12V Fuel PreFilter Cleaning

By unknown | Published: 22 Oct 2010

The maintenance schedule in the owners manual indicates the “strainer” should be cleaned at 12000 mile intervals at the same time the fuel filter is replaced. This is for both the “A” and “B” maintenance schedules. In the instructions in the service manual for replacing the fuel filter it states “Whenever the fuel filter is […]

Clutch Replacement

By unknown | Published: 23 Oct 2010

TOOLS: Tranny jack 2 or 3 ratchet straps porta power (this will make removing the cross member MUCH eaiser) A bottle jack and a piece of 4×4 will work in a pinch. Drill a hole in the end of the 4×4 to allow the bottle jack shaft to go in the 4×4 a couple of […]

P7100 Injection Pump Timing

By unknown | Published: 23 Oct 2010

THIS BULLETIN SUPERSEDES TSB. 18-10-94 DATED JUL.. 22, 1994. THE PART NUMBER FOR THE ENGINE TIMING TOOL PACKAGE HAS BEEN CHANGED TO SPX MILLER #6860. Models: 1994 (BR) Ram Truck Symptoms: Excessive white exhaust sake or lack of power. Diagnosis: Using the Mopar Diagnostic System (MDS) or the Scan Tool (DRB II or III) with […]

Top 3 Floor Mats for your Diesel Truck

By Andy | Published: 26 Mar 2010

It doesn’t take long to figure out that not all floor mats and liners are the same. Some offer great protection from the elements such as mud, snow, grime and dust, while others offer almost none. If you work in construction or any kind of industry that leavers your boots a little muddy at the […]

Triple Turbos on a Powerstroke Diesel

By dzljim | Published: 24 Oct 2010

THREE Turbos on a PSD!?! Well, it just had to be done. And it was a lot easier the second time around! Click HERE to see the build-up of the Twins. Much the same work and process was involved to create Stage 3, HT4B into HT3B into OEM Garrett. I really don’t know what to […]

Bosch VP44 Fuel Injection Pump Replacement

By Kent Earnest | Published: 23 Oct 2010

This documentation is intended to be used as a visual overview only and is not meant to be used as a replacement for a service manual. Please consult your Dodge service manual for complete instructions on the removal and re-installation of an injection pump The truck in this project is a 2000 Dodge Ram 3500 […]

Inspecting the Water Pump Weep Hole on Dodge Diesel Trucks

By unknown | Published: 23 Oct 2010

Use a pipe cleaner or a piece of wire to knock scale and dirt from the water pump weep hole. 1st and 2nd generation (every 12000 miles): 1: From above and just in front of the alternator pulley, look down to the water pump. 2: The weep hole is at about the 7:00 position, below […]

Diesel Fault Finding Chart

By unknown | Published: 23 Oct 2010

Symptom Key # symptom 1 Engine Running Hot 2 Poor Transient Response 3 Smoke 4 Engine Lacks Power 5 Black Exhaust Smoke 6 Blue Exhaust Smoke 7 High Oil Consumption 8 Turbocharger Noisy 9 Cyclic Sound From the Turbocharger 10 Oil Leak from Compressor Seal 11 Oil Leak from Turbine Seal   Note: R = […]

Dodge Cummins Ebrake ECM Hookup

By Ken Lenger | Published: 23 Oct 2010

Using the ECM to Control Non-Jacobs Exhaust Brakes You will need this pigtail to connect the brake wiring to the ECM. Cummins Part Number: 3824810 Connect the pigtail show above to pin 20 of the ECM Schematic for the Dodge/Jacobs e-brake system connected to the ECM You will need to adapt your e-brake installation to […]