Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Service Record Spreadsheet

By unknown | Published: 10 Nov 2010

Click the link below for the Excel version of Service Record Spreadsheet Service Record Spreadsheet [thanks to WBUSA used with permission]

Stewart Warner B749 Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B749 Gauge Install Sheet Stewart Warner B749 Gauge Install Sheet [thanks to Stewart Warner used with permission]

Dodge Diesel Injector Comparisons

By unknown | Published: 23 Oct 2010

By popular demand our customers have asked us to show a comparison between the Bosch 275hp RV injector and the Diesel Dynamics True Torque II injector series. This graph shows typical gains with the 275hp RV injectors and DD stages 1,2, and 3. This is a graph of a 99 Cummins Ram with Std Transmission. […]

Exhaust Stack Gallery

By unknown | Published: 23 Oct 2010

  Submit Yours !!!!

Another 24V Lift Pump Replacement Procedure

By Andy | Published: 23 Oct 2010

This is how I replaced the lift pump on my ’99 QC, 4×4. Not sure what variations may or may not accure on other models. Parts list…………..New lift pump, lift pump wire pig tail, banjo bolts washers (8), dielectric grease and approx 1/2 gallon of clean diesel. Tools ………. 3/8″ drive ratchet, 3 or 4 […]

Cummins Valve Cover Replacement

By dieselminded | Published: 10 Nov 2010

Here’s the Stocker And here’s the Bombed Valve cover Available Here at the Database: check the marketplace :: Bob Wagner The only tools you’ll need is a 1/4 inch drive ratchet and a 10 MM socket Really clean up the stock valve cover you do not want anything to fall down in to the valves […]

Control Module – ECMS

By unknown | Published: 23 Oct 2010

There are three computer modules which coordinate to control the Ram power train. Engine Control Module (ECM) – On the left side of the engine behind the fuel filter Fuel Injection Pump Control Module (FPCM) – On top of the injection pump Powertrain control module (PCM) – bolted to the Ram firewall under the hood […]

Dodge 24V IAT Sensor Cleaning

By Dean Isaacson | Published: 23 Oct 2010

This is an article for cleaning the IAT sensor on the 1998-2002 24V diesel engine. The IAT sensor measures the temperature of the intake manifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have […]

CTD Dimensional Specification

By Dean Isaacson | Published: 11 Nov 2010

2002 CTD/RAM Descriptions Specification Engine Type In-Line 6 Cyl. Turbo Diesel Bore & Stroke 102.0 X 120.0 mm 4.02 X 4.27 In. Displacement 5.9 L 359 Cu. In. Compression Ratio 245 HP 2002 CTD 235 HP 2002 CTD   17.0:1 16.3:1 Horsepower A/T M/T   235 @ 2700 RPM 245 @ 2700 RPM Torque Rating […]

Vulcan Fittings

By dieselminded | Published: 10 Nov 2010

This is a comparison between a Vulcan fitting and your stock banjo set up. The Vulcan Fittings are CNC Stainless Steal and are avalible with a tap in them for running a Fuel Pressure gauge. Vulcans Fitting replace The Stock Banjo’s at the following locations : VP44 inlet Fuel Filter Housing Inlet Fuel Filter Housing […]

Clutch Replacement

By unknown | Published: 23 Oct 2010

Start inside the truck. With a Phillips remove the screws holding the shift boot and slide it up. Remove shifter with 3/4″ or 19mm wrench. Pop up transfer case shifter boot and remove bolt/s. Pull out rubber inserts in cupholders and remove bolt/s. Remove plastic shroud. Unbolt shifter boot. Unbolt shift tower carefully and tape […]

Dodge Cummins HTT Manifold

By Kevin Whitmore | Published: 23 Oct 2010

After much reading of folks having troubles with the OEM manifold cracking and the bolts coming loose from expansion and contraction I decided it was time for me to go to a 3 piece manifold, I opted for the unit from High Tech Turbo and purchased one from my friend Lazer Bob in Colorado, The […]

A Recommendation for Trailer Pullers

By Wes Bailor | Published: 23 Oct 2010

I pull a 27 foot fifth-wheel RV trailer. I’ve had it all over the West. As you know, there is a hill or two out here. In fact just south of my town, Bend, Oregon, there is a grade that slowed my previous truck with this trailer to 45 mph top speed. I’ve always hated […]

Edge EZ Module Manual

By Dean Isaacson | Published: 8 Nov 2010

[thanks to Edge] Click the link for the pdf version of the Edge EZ Module Manual for the 24V CTD motor. Edge EZ Module Manual

Diesel Troubleshooting Chart

By unknown | Published: 24 Oct 2010

Complaint ————-> Probable Cause WillNotStart HardToStart StartsAndStalls DiesOnDeceleration RunsRough LackOfPower BlackSmoke WhiteSmoke Low Cranking Speed X X             Incorrect StartingProcedure X X             Some or All Glow Plugs Bad X X     X     X No Fuel to Cylinders X       […]