Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Bosch VP44 Fuel Injection Pump Replacement

By Kent Earnest | Published: 23 Oct 2010

This documentation is intended to be used as a visual overview only and is not meant to be used as a replacement for a service manual. Please consult your Dodge service manual for complete instructions on the removal and re-installation of an injection pump The truck in this project is a 2000 Dodge Ram 3500 […]

How to adjust the idle speed on a Dodge Diesel

By Andy | Published: 22 Oct 2010

How do I adjust the idle speed on my Ram diesel? The idle speed seems too high. First, trace the accelerator linkage to the connection on the fuel pump. With the ENGINE OFF have someone floor the accelerator and watch the fuel arm move. The best position I can describe is that it is under […]

Water Injection

By dieselminded | Published: 10 Nov 2010

Water Injection : Injecting water into the intake , Decreases the volume of each cylinder Sends the Pistons into Over Drive , add some alcohol to up the flash point of diesel and to be sure it all burns up and burns up fast and you have the complete package. Cooling Mist (www.coolingmist.com) Our Diesel […]

12V Cummins Governor Spring Kit

By unknown | Published: 23 Oct 2010

CAUTION:If you intend to operate the engine over 3200 rpm, you should replace the engine valve springs with a heavy-duty type. If you do not have heavy-duty exhaust springs installed please call PDR for further instructions. Estimated completion time: (First time installer) 1.5 hours Things you will need to complete this project: 1. 7/16″ deep […]

Dodge Pickup VIN Decoding

By unknown | Published: 11 Nov 2010

The Vehicle Identification Number (VIN) plate is located on the dash by the windshield near the left A-pillar. Position Interpretation Code Description 1 Country Of Orgin 3 Mexico 2 Make 8 Dodge 3 Vehicle type 6 Incomplete 7 Truck 4 Gross Vehicle Weight Rating K 8,001 – 9,000 M 10,001 – 14,000 5 Vehicle line […]

Pyro Tap Help

By dieselminded | Published: 23 Oct 2010

Install Help. Note: Tap Size May Vary [thanks to DIS dieselpage.com used with permission]

Relocating Your Block Heater Cord

By unknown | Published: 23 Oct 2010

As you know the block heater plug on our trucks are located in the front bumper and this is where they stay for most people. Some have put a plug recessed into the bumper to make it look nicer then having a cord dangling there. In my case being a Firefighter the way I park […]

Two Wheel Drive Low

By Andy | Published: 24 Oct 2010

The important thing is the 2 port vacuum switch…you need to get one that is ‘open’ when it’s in the off position so vacuum can flow through normally. I used a Nippondenso EGR vacuum switch for a Honda Civic. They never break! The rest of the parts list is simple and small: Rocker switch (I […]

On Board Air Tank

By dzljim | Published: 23 Oct 2010

It’s always handy to have compressed air with you for filling your flat tires, other people’s flat tires, air horns, blowing mulch or straw out of your bed, the list can go on and on.  I use compressed air mainly for my air horns. I’ve had a 9 gallon air tank in my aluminum bed […]

Weekend On The Edge 2006

By Dean Isaacson | Published: 11 Nov 2010

You could title this: My travels with Lem – Part II. Here we are on the road to the Weekend on the Edge event hosted by Edge Products of Ogden, Utah. The race is at the Rocky Mountain Raceway in West Valley City, Utah. This photo was taken at a rest stop in Montana. Funny, […]

Exhaust Stack Gallery

By unknown | Published: 23 Oct 2010

  Submit Yours !!!!

Cummins Valve Cover Replacement

By dieselminded | Published: 10 Nov 2010

Here’s the Stocker And here’s the Bombed Valve cover Available Here at the Database: check the marketplace :: Bob Wagner The only tools you’ll need is a 1/4 inch drive ratchet and a 10 MM socket Really clean up the stock valve cover you do not want anything to fall down in to the valves […]

NXD Stacker Nitrous System

By rodslinger | Published: 23 Oct 2010

SO you're on the fence about the whole Nitrous issue. Well what if there was a product out there that was mild enough for the daily driver, wouldn't break the bank to purchase and easy enough even the most novice shade tree mechanic could install it? Well here ya go – The guys at Nitrous […]

Dodge Diesel Truck Buyers Guide

By unknown | Published: 23 Oct 2010

Every Vehicle, Every Model On earth has its fair share of issues, And our CTD/RAMS are no exception This article is not meant to point out problems you’re going to have its just a heads up to some common known issues. To Learn Even More Join www.TDR1.com These Problems Affect all Years: Steering wander, 5th […]

24V CTD Valve Lash Limits

By unknown | Published: 11 Nov 2010

Spec Intake Exhaust Minimum 0.152 mm (0.006 inch) 0.381 mm (0.015 inch) Standard 0.254 mm (0.010 inch) 0.508 mm (0.020 inch) Maximum 0.381 mm (0.015 inch) 0.762 mm (0.030 inch) Adjustments should only be performed when the engine coolant temperature is less than 60°C (140°F).