Post Your Successful Diesel Mods At Dieseldatabase

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Ford 6.0L Intercooler Swap for the 7.3L Powerstroke

The swap is relatively inexpensive and not to time consuming. Used 6.0 intercoolers can be had on eBay for around $100-$125. The 6.0 IC is about 30% larger than the 7.3. The original 7.3 PSD intercooler measures 30x18x2 and the 6.0 PSD is 30x21x2.25. One thing you should be aware of before you stat taking […]

Installing Upfitter Switches in 2005 and Newer Ford Super-Dutys

If you want to add a few aftermarket options to your new Ford Super Duty, Ford Motor Company makes things easy for you. One of the options you can select from the factory is the “UPFITTER SWITCH” option. This is a bank of four switches, with fuses and associated relays, that provide two 30 amp […]

Stewart Warner B779 Add-On Shift Light Install Sheet

Click the link below for the pdf version of Stewart Warner Add-On Shift Light Install Sheet Stewart Warner Add-On Shift Light Install Sheet [thanks to Stewart Warner used with permission]

Dodge 12V Cummins Fuel Shutdown Solenoid

To check the fuel solenoid adjustment: 1. Turn the key on but do not bump the starter 2. Get under hood and pull up the solenoid by hand (it will stay up when you let go). 3. Measure from the bottom of the solenoid mounting bracket to the top of the lever pin as shown […]

Rust Prevention

Here’s a convenient and easy method of applying rust preventing solutions to inner panels and seams to control or avoid rust to various body seams. The nicest feature, is that you don’t have to remove interior panels to apply, just insert the feed hose into where you want to apply your rustproofing. The specific solutions […]

Cleaning Stickum – Part 2

This is a followup article to Cleaning Stickum Left From Vinyl After the last article regarding removing the stickum leftover from vinyl lettering and signs, several people got hold of me to let me know of their remedies. DM left a comment on the article site about peanut butter removing residue left behind by decals. […]

Dodge 24V IAT Sensor Cleaning

This is an article for cleaning the IAT sensor on the 1998-2002 24V diesel engine. The IAT sensor measures the temperature of the intake manifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have […]

Stewart Warner B754 Gauge Pods Install Sheet

Click the link below for the pdf version of Stewart Warner B754 Gauge Pods Install Sheet Stewart Warner B754 Gauge Pods Install Sheet [thanks to Stewart Warner sw-performance.com used with permission]

Air Dog Install Manual

[thanks to Air Dog] Click the link for the pdf version of the Air Dog Installation manual for the 24V CTD. Air Dog Installation manual

A Good Chain Can Make All The Difference

I cannot describe the feeling but I know you’ve felt it before. The feeling you get when you know something is enormously wrong but just before the full impact hits you. It was only five fifteen but it was dark outside. I stepped outside my truck and was looking back at the trailer. From where […]

Dodge Pickup VIN Decoding

The Vehicle Identification Number (VIN) plate is located on the dash by the windshield near the left A-pillar. Position Interpretation Code Description 1 Country Of Orgin 3 Mexico 2 Make 8 Dodge 3 Vehicle type 6 Incomplete 7 Truck 4 Gross Vehicle Weight Rating K 8,001 – 9,000 M 10,001 – 14,000 5 Vehicle line […]

Pyro Tap Help

Install Help. Note: Tap Size May Vary [thanks to DIS dieselpage.com used with permission]

Another 24V Lift Pump Replacement Procedure

This is how I replaced the lift pump on my ’99 QC, 4×4. Not sure what variations may or may not accure on other models. Parts list…………..New lift pump, lift pump wire pig tail, banjo bolts washers (8), dielectric grease and approx 1/2 gallon of clean diesel. Tools ………. 3/8″ drive ratchet, 3 or 4 […]

Turning Up a P7100 Pump

The steps for turning up a P7100 pump are: 1) Remove your AFC Housing 2) Mod Your Fuel Plate either slide it forward or purchase a cut one 3) Adjust the governor lever to contact the fuel plate 4) Crank the star Wheel Towards the motor 5) Slide The AFC housing all the way forward […]