Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Dodge Cummins Ebrake ECM Hookup

By Ken Lenger | Published: 23 Oct 2010

Using the ECM to Control Non-Jacobs Exhaust Brakes You will need this pigtail to connect the brake wiring to the ECM. Cummins Part Number: 3824810 Connect the pigtail show above to pin 20 of the ECM Schematic for the Dodge/Jacobs e-brake system connected to the ECM You will need to adapt your e-brake installation to […]

Superchips 3705 Chart and Installation

By unknown | Published: 23 Oct 2010

7.3L Powerstroke Custom Fuel System

By Andy | Published: 23 Oct 2010

Bigger injectors require more fuel. Lots more fuel than what the oem system can put out. And the oem stuff has many faults, which just makes it that much more appealing to replace the whole darn system! I was planning on doing some work to the truck and I knew it would be laid up […]

Stewart Warner B751 Air Fuel Ratio Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B752 Air Fuel Ratio Gauge Install Sheet Stewart Warner B752 Air Fuel Ratio Gauge Install Sheet [thanks to Stewart Warner used with permission]

Relocating Your Block Heater Cord

By unknown | Published: 23 Oct 2010

As you know the block heater plug on our trucks are located in the front bumper and this is where they stay for most people. Some have put a plug recessed into the bumper to make it look nicer then having a cord dangling there. In my case being a Firefighter the way I park […]

Glossary of Diesel Terms

By dieselminded | Published: 10 Nov 2010

2WD – Only one pair of wheels are driven by engine power 4WD – One or both pairs of wheels are driven by engine power. 454 CUBIC INCH – Large gasoline engine option available in full size Chevy/GMC Trucks and Motorhomes. 460 CUBIC INCH – Large gasoline engine option available in full size Ford Trucks […]

Heated Tow Mirror Swap

By unknown | Published: 23 Oct 2010

You need to have the bases from an 2nd gen. tow mirror equipped truck. Then purchase a set of Power/heated tow mirrors from a 3rd gen truck, you can get them in a kit (which is both mirrors, you will still need to buy a switch, knob and nut) Once you have all four mirrors, […]

Ford 7.3L Engine Removal – The REAL How To

By dzljim | Published: 23 Oct 2010

After replacing my rear axle cover due to rust through, I noticed severe rust on the engine oil pan. I’ve had experiences with rusted oil pans in the past and knew this had to be taken care of soon, or I’d be doing it in the middle of an Ohio winter. Early October, 2001, I […]

Twin Electrical Fans

By dzljim | Published: 24 Oct 2010

It’s been said that the factory fan consumes horsepower, and I’ve heard conflicting results as to what the power increase would be if you were to eliminate the fan and go electric. Me, I just don’t like the idea of that big thing swinging around on the end of the water pump, putting all that […]

Ford 7.3L Diesel Fuel Tank Vent Mod

By dzljim | Published: 23 Oct 2010

About one month after I completed the extraction and re-installation of the PSD from my truck, necessitated to replace a rusted out oil pan, I noticed diesel fuel on the floor of my garage under the rear of my truck.  Sure enough the steel rear fuel tank had also rusted through.  Why in the world […]

Stewart Warner B779 Add-On Shift Light Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner Add-On Shift Light Install Sheet Stewart Warner Add-On Shift Light Install Sheet [thanks to Stewart Warner used with permission]

Old 12v Cummins Boost Guage Installation

By Andy | Published: 23 Oct 2010

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]

Upgrading to 16cm Exhaust Housing

By dieselminded | Published: 8 Nov 2010

With this guide we have a donor charger so Removal of the charger is not included Refer to the Charger Swap Guide for further information Completion time: Less than 2 Hours Here’s a 16cm Holset Exhaust Housing Here’s the Exhaust Gasket Here’s the Oil Return Line Gasket Here’s the donor charger This set up is […]

Efficient Engine Montoring

By dieselminded | Published: 10 Nov 2010

PYRO: Temperatures will vary whenever the throttle is moved or the terrain changes. The peak number is the most important while towing, the ISB can be safely run up to 1450 for short bursts and 1350 all day long. This number is strongly affected by modifications weather it be Air flow or Fuel delivery. If […]

Top 3 Floor Mats for your Diesel Truck

By Andy | Published: 26 Mar 2010

It doesn’t take long to figure out that not all floor mats and liners are the same. Some offer great protection from the elements such as mud, snow, grime and dust, while others offer almost none. If you work in construction or any kind of industry that leavers your boots a little muddy at the […]