Post Your Successful Diesel Mods At Dieseldatabase

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Dodge Towing Specifications

When Equipped with Cummins Turbo Diesel Dodge RAM 2500 RAM 2500 Reg Cab 4×2 Long Bed Quad Cab 4×2 Short Bed Quad Cab 4×2 Long Bed Trans/Axle GCWR Payload Curb Wt Tow Wt Payload Curb Wt Tow Wt Payload Curb Wt Tow Wt A4/3.55 16,000 3,120 5,679 10,150 2,820 5,981 9,850 2,700 6,096 9,750 A4/4.10 […]

Ram Diesel Lift Pump Replacement

Tools needed: 7/16 or 11mm socket – for boost tube clamps 10mm socket – for lift pump bolts 14mm socket – for fuel filter canister 3/8 ratchet 6″ 3/8 extension 3/8 universal joint – makes filter nut easier 3/4″ open end wrench – for fuel inlet nut 14mm open end wrench – for fuel outlet […]

4 Inch Turbo-Back Kit Number 4005500

Click the link to view the instructions for Turbo-Back Kit #4005500 instructions for Turbo-Back Kit #4005500

Diesel Fault Finding Chart

Symptom Key # symptom 1 Engine Running Hot 2 Poor Transient Response 3 Smoke 4 Engine Lacks Power 5 Black Exhaust Smoke 6 Blue Exhaust Smoke 7 High Oil Consumption 8 Turbocharger Noisy 9 Cyclic Sound From the Turbocharger 10 Oil Leak from Compressor Seal 11 Oil Leak from Turbine Seal   Note: R = […]

Crankshaft Position Sensor Replacement

(1) you need to disconnect both negative battery cables at both batteries. I used a 1/2 inch deep socket to remove the cables from the battery terminals. (2) Remove starter motor to get to CKP. The sensor is located on the driver’s side of the engine with the starter motor placed in front of it. […]

Glossary of Diesel Abbreviations

2WD Two Wheel Drive 4WD Four Wheel Drive AAMOF As A Matter Of Fact – used by many on mail lists and message boards ABS Anti-lock Brake System: Modulates braking pressure to control wheel lockup ACM Airbag Controller Module: monitors sensors and deploys airbag(s) in the event of an accident ACT Air Charge Temperature ACV […]

Exhaust Stack Gallery

  Submit Yours !!!!

Cummins Governor Spring Replacement Aid

Here’s the dust cover that needs to be removed to access the governor springs Once the dust cover is removed you’ll need to turn the motor over till a set of springs is lined up perfectly in the opening … there are 2 sets of springs they are mounted opposite of each other Here’s how […]

Dodge 12V Cummins Fuel Shutdown Solenoid

To check the fuel solenoid adjustment: 1. Turn the key on but do not bump the starter 2. Get under hood and pull up the solenoid by hand (it will stay up when you let go). 3. Measure from the bottom of the solenoid mounting bracket to the top of the lever pin as shown […]

Turning up the Injector Pump on a 7.3L or 6.9L IDI

This article will hopefully give you some insight on how to adjust your fuel injection pump on 88-93  7.3L Non-Powerstroke, IDI. This will probably work the same way on a 6.9L Navistar(Ford) engine as well. To start off, I would recommend putting in a pyrometer gauge before doing any kind of performance upgrades. I would […]

Detailed Dodge Diesel Oil Change

Supplies: 3 Gallons Oil; Mobil Delvac Super 1300 is what I use, I should probably be using the Synthetic stuff. But I don’t. Oil Filter; My Fleet Guard Filter supply was tapped out so I had to run to advanced auto and get a Purolator… $15 !! The Fleet Guard Filters can be had for […]

Weekend On The Edge 2006

You could title this: My travels with Lem – Part II. Here we are on the road to the Weekend on the Edge event hosted by Edge Products of Ogden, Utah. The race is at the Rocky Mountain Raceway in West Valley City, Utah. This photo was taken at a rest stop in Montana. Funny, […]

Boost Gauge Installation on Dodge Cummins

1. A hole must be drilled and tapped into the intake crossover pipe for a boost source. 2. Remove the hose from the intake crossover pipe and push a rag well into the pipe past the point to be drilled and tapped. This will prevent chips from entering the engine. 3. Drill through the back […]

Ram Injector Specs

Fuel Injector ” Pop Off ” Pressure: 31,026 kPa (310 bars) or (4500 psi +/- 250 psi) Fuel Injector Leak Down Pressure: App 20 bars (291 psi) lower than pop pressure Fuel Injector Firing Order: 1-5-3-6-2-4

Air Dog Install Manual

[thanks to Air Dog] Click the link for the pdf version of the Air Dog Installation manual for the 24V CTD. Air Dog Installation manual