Post Your Successful Diesel Mods At Dieseldatabase

By Dean Isaacson | Published: 7 Mar 2011

Have you completed a successful mod on your diesel truck? and did you take pictures and discovered tips that might help others? Your post is welcome here. All you have to do is register on this site. Then contact us via the the contact form on the ABOUT page (see menu), letting us know you […]

Stewart Warner B753 Pillar Pod Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B753 Pillar Pod Install Sheet Stewart Warner B753 Pillar Pod Install Sheet [thanks to Stewart Warner sw-performance.com used with permission]

The Dodge Diesel Mystery Switch

By unknown | Published: 23 Oct 2010

These instructions for the mystery switch are for the 47RH not the 47RE. The later transmission control has a relay that has to be removed and the load pins jumped. The ’96 and later also have more than one orange with black tracer wires on the PCM. There are 2 (two) options you have between […]

24V CTD Valve Lash Limits

By unknown | Published: 11 Nov 2010

Spec Intake Exhaust Minimum 0.152 mm (0.006 inch) 0.381 mm (0.015 inch) Standard 0.254 mm (0.010 inch) 0.508 mm (0.020 inch) Maximum 0.381 mm (0.015 inch) 0.762 mm (0.030 inch) Adjustments should only be performed when the engine coolant temperature is less than 60°C (140°F).

12V Cummins Thermostat Replacement

By unknown | Published: 24 Oct 2010

Symptom/Condition: The vehicle may not warm completely, especially in cold ambient temperatures. This condition may be due to a thermostat that is stuck in the partial open position by debris in the cooling system. NOTE: THE COOLING SYSTEM USED ON THE CUMMINS DIESEL ENGINE EQUIPPED VEHICLES PROVIDES THE CAPACITY AND PROTECTION OF THE HIGHER GVWR […]

Stewart Warner B806 Exhaust Temp Gauge Install Sheet

By unknown | Published: 10 Nov 2010

Click the link below for the pdf version of Stewart Warner B806 Exhaust Temp Gauge Install Sheet Stewart Warner B806 Exhaust Temp Gauge Install Sheet [thanks to Stewart Warner used with permission]

Dodge 24V Cummins Lift Pump Replacement

By unknown | Published: 23 Oct 2010

Procedures for a 1999 Ram NOTE: You may be able to improve this but this is exactly what we did and changed two pumps in less that two hours) TOOLS: 17 mm wrench & socket, 10 mm wrench & socket, 7/16 socket, 1/2 inch socket. 1. Lay a non-conducting material over the battery posts (fender […]

Inspecting the Water Pump Weep Hole on Dodge Diesel Trucks

By unknown | Published: 23 Oct 2010

Use a pipe cleaner or a piece of wire to knock scale and dirt from the water pump weep hole. 1st and 2nd generation (every 12000 miles): 1: From above and just in front of the alternator pulley, look down to the water pump. 2: The weep hole is at about the 7:00 position, below […]

Dodge Diesel Truck Buyers Guide

By unknown | Published: 23 Oct 2010

Every Vehicle, Every Model On earth has its fair share of issues, And our CTD/RAMS are no exception This article is not meant to point out problems you’re going to have its just a heads up to some common known issues. To Learn Even More Join www.TDR1.com These Problems Affect all Years: Steering wander, 5th […]

China can make things cheaper than the US – Here’s How!

By unknown | Published: 23 Oct 2010

Ever Wonder How China makes Stuff Cheaper than us? China needs “fair trade” instead of “free trade,” and maybe the greater profit margins will make room for OSHA, EPA, and some of the other trappings that make America great! The Construction Site Hard Hat The Dust and Particle Free Breathing Apparatus OSHA Approved Scaffolding And […]

Port and Polishing

By unknown | Published: 23 Oct 2010

First, you will need cutters. In the next photo you will see some of the cutters I use for this. On the right are metal cutters. These cost $20 to $75 each, so choose wisely. In the middle are sanding cones. I use #80-100-220-240 grit. I use a long mandrel and a (not shown) short […]

Dodge 24v Cummins Injector Replacement

By unknown | Published: 23 Oct 2010

Here is a sheet for replacing the injectors on a Dodge 24v Cummins [thanks to Diesel Dynamics] DD-Injector-Install-Instructions

Fuel Filter Usage

By unknown | Published: 23 Oct 2010

Here’s a photo showing the condition of my original fuel filter after 24,000 miles – never been changed to this point since new: The photo is a bit misleading the overall condition of the old filter is actually not bad at all – lots whiter down in between the pleats than can be seen here, […]

A Recommendation for Trailer Pullers

By Wes Bailor | Published: 23 Oct 2010

I pull a 27 foot fifth-wheel RV trailer. I’ve had it all over the West. As you know, there is a hill or two out here. In fact just south of my town, Bend, Oregon, there is a grade that slowed my previous truck with this trailer to 45 mph top speed. I’ve always hated […]

Glossary of Diesel Abbreviations

By dieselminded | Published: 23 Oct 2010

2WD Two Wheel Drive 4WD Four Wheel Drive AAMOF As A Matter Of Fact – used by many on mail lists and message boards ABS Anti-lock Brake System: Modulates braking pressure to control wheel lockup ACM Airbag Controller Module: monitors sensors and deploys airbag(s) in the event of an accident ACT Air Charge Temperature ACV […]

24V Transmission Pan Comparisons

By dieselminded | Published: 24 Oct 2010

By adding an increased capacity transmission pan you decrease your fluid temperature and prolong the life of your transmission. Here are some options: Hughes (www.hughesperformance.com) Bolt on deep transmission pans are made from cast aluminum and designed with cooling fins to dissipate heat quicker. Cast aluminum pans hold approximately 2 to 4 extra quarts of […]